GREEN-GO PARTYLINE HIRE.

Green-GO beltpacks take audio and power down one network cable from a PoE switch. There is no matrix to set up: every device holds the configuration and finds the others.

A system is beltpacks on a switch, with an Interface X in the rack where it has to meet a partyline or a four-wire circuit.

Green-GO Beltpack X wired intercom beltpack

Green-GO

BELTPACK X WIRED BELTPACK

GGO-BPX

The wired beltpack: one network cable for audio and power, a colour display that names each channel, and four buttons that can be set to two, three or four channels.

Request a quotation →
Channels
2, 3 or 4 on the buttons; access to all 32
Controls
4 buttons, 2 push-rotary encoders
Display
0.95-inch colour OLED
Headset connector
4-pin male XLR
Network
1 × etherCON RJ45
Power
PoE 802.3af; 2 W typical, 5 W maximum
Dimensions
95 × 119 × 46 mm
Weight
261 g
Operating temperature
0 to 55 °C
Green-GO Interface X two-wire and four-wire audio interface, 1U rack unit

Green-GO

INTERFACE X TWO-WIRE AND FOUR-WIRE

The interface between Green-GO and analogue audio. One two-wire port takes an existing partyline, and two four-wire circuits take programme feeds, a matrix port or a link to a broadcaster.

  • Joins an analogue partyline to Green-GO
  • Two four-wire circuits in and out
  • Two network ports with a built-in switch
  • PoE or 12 V DC, and both for redundancy
Request a quotation →
Two-wire
1 × XLR female, with switchable termination
Four-wire in
2 × line in on XLR female
Four-wire out
2 × line out on XLR male
Two-wire level
6 dBu maximum
Configurations
Not for systems set to 48 kHz
Green-GO Beacon signal light for calls and cues

Green-GO

BEACON SIGNAL LIGHT

A light that shows a call or a cue, in the colour of the channel it came from. It is for the places where a call tone would be heard by an audience, or not heard at all over the noise.

  • Shows a call in the channel’s own colour
  • Powered from the network cable
  • Mounts on a microphone stand thread
Request a quotation →
Function
RGB signal light for calls and cues
Network
1 × etherCON RJ45
Power
PoE 802.3af or USB; 2.5 W typical
Mounting
3/8-inch thread
Dimensions
95 × 119 × 41 mm
Weight
232 g

WORKS WITH

The equipment this is usually hired with.

Green-GO HS200S single-ear intercom headset

Green-GO

HS200 HEADSETS

Single and double ear, with a dynamic microphone and a coiled cable.

Specifications →
Green-GO Multichannel X rack-mount intercom station

Green-GO

MULTICHANNEL X

A 32-channel station with three touchscreens, for the rack or the desk.

Specifications →
Green-GO Wireless Beltpack X DECT intercom beltpack

Green-GO

WIRELESS BELTPACK X

The Green-GO beltpack without the cable, and the antennas that connect it to the network.

Specifications →
Green-GO Interface X two-wire and four-wire audio interface, 1U rack unit

Green-GO

INTERFACE X

The interface between Green-GO and analogue audio.

Specifications →

MORE IN WIRED INTERCOM

Riedel Performer C3 two-channel digital partyline beltpacks, front and rear

Riedel

PERFORMER C3

Two-channel digital partyline beltpacks on ordinary XLR cable, with the interface that powers them.

Specifications →
Clear-Com HelixNet HXII-BP-4K four-channel digital partyline beltpack

Clear-Com

HELIXNET

Digital partyline on the cable a venue already has: beltpacks, a rack station and the Arcadia that hosts them.

Specifications →
Clear-Com Encore RS-701 single-channel analogue partyline beltpack

Clear-Com

ENCORE

Analogue partyline on microphone cable: one and two-channel beltpacks and the main station that powers them.

Specifications →

All wired intercom →Everything from Green-GO →

  • Specifications are the manufacturers’ published figures and can change with hardware and firmware revisions. Product names and trade marks belong to their owners.

NEED IT ON A SHOW?

Tell us the dates, the venue and roughly how many people need to talk. You will get a written quotation covering equipment, engineering time and delivery.

Request a Quotation →Get in Touch →